There are plenty of reasons to install new indoor light fixtures in your home. Perhaps you want to update your interior aesthetic, or save energy by upgrading to efficient LED bulbs. Maybe you even want to bring your lighting into a smart home control system. Although wiring a new fixture is usually a simple job, complications can crop up if your home still uses an outdated wiring system. In order to comply with your local building code, you may have to perform some extra electrical work to ensure the safety of your new fixture. Read on to learn more.

Bringing Older Electrical Work Up to Code

If your home still uses knob-and-tube wiring, the law prohibits connecting new light fixtures to the old wiring. You don't have to replace the entire wiring system itself, although that’s not a bad idea, because it can reduce your risk of an electrical fire and lower your insurance rates. Even if you don't have the time or money for such extensive electrical work, though, you can remain in compliance with your local code by installing an electrical box between your wiring and the light fixture.

You can purchase an appropriate electrical box at most local hardware stores – but make sure you verify that it is designed to meet local code guidelines for installing new light fixtures. From there, after you turn off the power to the room, you have to cut a hole in the wall where you want the fixture to go, large enough for the box to fit. If you're lucky, the fixture will be near a stud or part of the frame so you can mount the box easily. Otherwise, you have to cut the wall extremely carefully to ensure you leave enough lath and plaster keys to support the box.

Wiring the New Light into Place

Next, once the box is ready to be installed, follow the manufacturer instructions to clamp in the home wiring to the back of the unit. You may have to add a ground wire as well, depending on the specific scenario. Anchor the box using metal supports, and when it's all in place, connect the light fixture. When everything is securely connected, you can turn the power back on and give your new light a trial run.

Remember, knob-and-tube wiring can be a fire hazard, and performing electrical work in general can be dangerous if you don't know what you're doing. If you have any doubts or questions about installing your new light fixture, the best route is to have a professional electrician give you a hand.

Expert Assistance with Your Electrical Work

For assistance with all your electrical work, including installing new light fixtures, contact a qualified residential electrician today.

Electricity savings help customers to reduce the energy bills and environmental degradation. With technology becoming more affordable, most households are increasingly relying on electrical appliances. However, inefficient equipment or usage ends up costing the consumer more money unnecessarily.  Low electricity consumption not only saves the energy costs, but also means using less fossil fuel, nuclear and coal to generate the power.

Consumers have all the control on their power needs, and the best way to achieve electricity savings is by understanding all the requirements and then optimizing the way they use the appliances. While some users might not be aware of the many small things they can do to reduce their reduce electricity costs.

Although most electrical fires start very small, they can quickly spread into almost unmanageable proportions. This is especially true if the fire starts behind your walls. This can lead to a fire becoming very large before you even realize that it is there. Your best protection against an electrical fire is to prevent it from happening in the first place. If you must deal with one, however, you should always be prepared to take the proper course of action. Whenever faced with an electrical fire, your own personal safety is the number one priority. If the fire is too large for you to contain, or is growing too quickly, evacuate everyone out of the home immediately until a fire crew can make the area safe again.

If you are in a position to control the fire, start by shutting off all power to your building. Simply go to the electrical panel and shut off the main breaker until the fire is under control. If you do not already know where this is, find its location and make sure that it is never blocked or obstructed. Once the power has been shut off, you can attempt to smother the fire with a Class C fire extinguisher or baking soda. Do not ever throw water on an electrical fire. Water conducts electricity, which can result in you or someone else becoming electrocuted. Whenever the fire has been controlled, do not turn your electricity on until an electrician in Pasadena has inspected your wiring for safety. The last thing that you want is for a second fire to occur in the same place.

When it comes to using electricity in your home and businesses, your safety is more important than any other factor. Learn how to use your electrical system safely so that you can avoid any electrical fires, shocks or other mishaps. For more tips and information on fire safety and services, visit The Electric Connection website at www.theelectricconnection.com/.