You Can Be Liable for Unlicensed Electrical Work

07/30/15

Revamping your home's electrical work can be a big headache. You need to find a qualified electrician and write what could be a hefty check for work that might require opening holes in your walls and temporarily making a mess of your home. The last thing you want after a big electrical project is to have to tear it all out and redo the job all over again. That could be the scenario you face, however, if you cut corners and don't hire a licensed electrician to take on the task. Fly-by-night contractors might be cheaper at the outset, but they can cost you big time in the end if they don't follow the local building code, leaving you liable for the faults in your home wiring.

Fanning the Building Code Fires

Some contractors might complain about having to follow local code, but it's in place for a reason – it helps ensure that any work done on your home is performed safely and effectively. Local code standards are particularly important when it comes to electrical work, because faulty wiring and connections can lead to short circuits or even an electrical fire, putting your family at risk.

That's why technicians who do electrical work are required to maintain a license, secure permits and schedule inspections for many home projects. Unfortunately, there are electricians who are tempted to skip the code requirements in order to avoid the time and expense of compliance. They might quote you a lower price, but shoddy workmanship can leave you on the hook for a lot more money overall.

Limit Your Exposure to Liability

If your local government figures out that you are working on an electrical project, they can send an inspector to check it out. If the work isn't up to code, you'll have to remedy the problem before you pass inspection. And if your electrician isn't licensed, you have little recourse to correct the faulty electrical work besides paying out of pocket for someone else to redo the entire thing. Worse, if your electrical system does cause a fire that leads to injury or death, you could be civilly liable for huge sums.

Licensed electricians, on the other hand, have more incentive to follow the rules to begin with, since they could lose their certification if they don't. Furthermore, you may have an easier time recouping your investment in the event of unsafe or incomplete work if you can prove that you did your due diligence and hired a licensed electrician.

Good Work Done Right

To avoid code and permitting issues, hire only licensed technicians for your electrical work and ask them to show you all the relevant permits. Protect yourself and your home by holding out for competent contractors so you know the work is done right the first time.

Advanced lighting control systems (ALCS) utilize electronic circuits with a programmable logic controller to automatically adjust lighting levels.  Program a number of variables and light requirements to get the lighting just perfect. This helps in providing the right amount of light where and when it is needed, hence improving energy efficiency and savings.

Advanced lighting control systems provide benefits like automatic scheduling and dimming. Turn lights off based on room occupancy and level of daylight. In so doing, the ALCS adjusts the light levels to match the requirements at any particular time. For example, when a room is empty, lights dim or go off completely. This saves on utility costs.

The sensors communicate with the lighting control system through wired or wireless connections. In some applications, sensors are integrated into the lighting control. While the wired network requires hand wiring of all the devices, the wireless communications use radio frequencies. Therefore several benefits exist over the wired network.

Wireless technology eliminates the need for wiring and is, therefore, cheaper, easy to implement and modify. It provides more flexibility while reducing the planning time for the electrical system. Wireless lighting controls are ideal for hard-to-reach lights. These include places where there are non-accessible or hard ceilings, basements, and other expensive or hard-to-wire areas.

The controller automatically adjusts the level of illumination based on one or a combination of the following variables.

The controls utilize room occupancy or proximity sensors to check for activity in the room or target area. If there is no activity, the controls automatically switch off or dim the lights. The system will then turn the lights to full brightness when room occupancy sensors detect someone within a defined space.

Different lighting levels are required based on the activity. In some applications such as warehouses, there is no need to keep all the lights on when areas are not in use. The lighting control systems will either turn off or dim most of the lights. Some advanced systems provide just enough light in the open spaces. Yet, more light becomes available near shelves where a worker might be picking up or replacing items.

Additional light is required during office hours when people are working. However, this isn’t necessary during the lunch break, or when offices are being cleaned. A combination of controls may be used here. Take advantage of daylight, dim or completely turning off the lights when more natural light filters into the room.

The programmable controls can be used to switch individual or groups of lights depending on time of day. These programs run 7 days a week. Consequently, there’s a separate schedule for weekdays, weekends, and holidays. In an office setup, a timer ensures that all lights, apart from security lights, are turned off at night, during the weekends and on holidays.

Instead of using the lamp at its maximum rating when new, the controls dim the light in certain cases. This reduces the normal wear and tear. As the lamp ages, its level of illumination will decrease. However, instead of the light level going down, the control will decrease the dimming level and maintain the required level of light.

So instead of powering the light at 100% and wasting energy with excess light that is not required, the controller ensures light is powered at a lower percentage. This ensures that required light is provided, but at a lower power consumption.

Factors considered when implementing a lighting system include the need for flexibility, facility size, floor plans, facility use, daylight hours, and building codes. Other considerations include the cost-effectiveness of the system, the ease of use, visual performance and comfort.

In addition to controlling the lights, the advanced lighting control systems help in determining the occupancy patterns. Moreover, the operating status of part or whole sections and the entire system’s performance is monitored. This provides business owners with an opportunity to evaluate the effectiveness of the installation and make adjustments.

From movies candle-lit dinners, lighting is one of the most important factors in everything we do.  Science and technology teams around the world have put an amazing amount of effort into developing the sturdiest, longest-lasting lights for any application you can think of.  Color, saturation, brightness, and even beam shape are all important when it comes to picking the right light for the situation.  The best part?  Mood lighting is a careful art that’s pretty easy to pull off once you know which settings work best.  Romantic lighting is especially simple and can set the stage so long as you have the right room and the right lights.

It could be our culture that has led us to see certain settings as romantic.  But there are also a few scientific aspects of lighting that genuinely make a setting more romantic.  While it may be that decades of amber-colored lights or the flicker of candlelight have fashioned our notions of what makes for romantic lighting, there’s also the effect of the light itself to consider.

Light with a low color temperature (below 3000K, or ‘yellow’ light) produces a very interesting effect on surfaces.  These lights, which are standard for most incandescent lamps, soften features and improve appearances.  If you want to look good, use an incandescent lamp.  While not ideal for getting ready in the morning, a standard light gives that warm and cozy feeling we all enjoy from standard incandescent bulbs.

The next step is to keep the lights dimmer than normal.  Dimmer lighting creates a closer, more intimate feeling to any room.  But there is a trick to this.  Don’t simply remove a few light bulbs from the dining room, you need to use an actual dimmer.  Uneven lighting is jarring and distracting.  Removing lamps or relying on recessed lights that have been dimmed can ruin the effect.  Recessed lighting that’s been dimmed can create cave-lighting (when there are unintended dark corners along the upper part of the wall).  Uneven lighting isn’t cozy, it’s distracting.  Use a dimmer switch.  Just be sure to match your dimmer to the type of lights you’re using.  If you plan to use LED lamps, make sure the dimmer is compatible with your brand of LEDs.

When we say to keep lighting even, we don’t mean equal throughout the room.  Even lighting in this case is designed to highlight focus areas.  Think about how restaurants stagger their lighting, with islands of light at each table and muted lights everywhere else.  If you want the greatest effect, use a fixture that focuses a soft light where you’ll be spending your time while ambient lighting casts a light glow everywhere else.

A romantic setting demands more than just the right lighting.  Pair the lighting with a favorite meal or entertainment.  Some background music will set things off nicely, but only if you select something that matches the mood.  You may enjoy electronic dubstep, but when the lights are lower something quiet and soothing is the way to go.

For the best in quality electrical repair work and installations, contact the professionals at Custom Electric!  Be sure to check back here each week for helpful advice, news, and guides or follow us on Facebook and Twitter!

Categories: Holiday Lighting« Why You Should Use a Surge Protector  |  What is a Circuit Panel? »