The start of the new school year for kids means cooler weather is just around the corner! The Farmer’s Almanac is predicting another wicked cold winter, with our area getting cold, wet, and white…yikes!

Since winter is often the time when energy bills are the highest, we thought we’d share a few of our favorite energy saving tips to help keep you comfortable without breaking the bank this season. Keeping your electrical system safe is important, especially when snowstorms threaten to knock out power (and with it, heat!), so read up and remember: for all your electrical service needs in Maryland, Virginia, and Washington, DC, call Kolb Electric!

If you use a heat pump to heat and cool your home, you probably already know that they’re among the most efficient HVAC systems you can install—if you use them correctly.

During the winter, set your thermostat to the lowest setting you’re comfortable with and keep it there for the whole season—the U.S. Department of Energy (DOE) recommends 68 F, but ultimately this is up to you. Every degree you set the thermostat lower will lower your energy use, so if you like to bundle up, this is a great way to save!

Most heat pumps come with a backup heating system to give you a little extra heat if the pump itself can’t make it. Unfortunately, electrical resistance heat is very inefficient and can get expensive if you use it too often. This electrical backup kicks on when you turn your thermostat up, which is why it’s best to set your thermostat once during the winter and then leave it there.

The one time when you should adjust your thermostat is when you’re leaving the house for a few days—the backup heat will kick on when you come back and set it back up, but the amount you save from being gone should offset that.

With any other form of heat, you’re free to adjust the thermostat as needed throughout the day. Again the DOE recommends 68 F as a balance between comfort and efficiency, but you may want to set the thermostat lower during the day when you’re not home and higher when you are home (a programmable thermostat makes this easy!).

If you’re going to be away and want to set the thermostat down, don’t go lower than 55 F. If your home gets too cold, your pipes could freeze and create a very messy situation for you when you return!

Whatever type of heating system you use, make sure you keep your filters fresh all season. Change them about once a month during times of peak heating system use. Just keeping on top of this can save you as much as 10 – 15 percent on your monthly energy bills!

Your water heater is usually the second largest energy consumer in your home, next to your heating system. Saving money on your water heating is not too complicated:

Fix all leaks when they happen! Even what looks like a small leak can waste hundreds of gallons of water per month—all of which you still have to pay for.

Take showers instead of baths. A normal shower uses about half the water of a bath, which also means less water heater needs, lower sewer costs, etc.

Use a flow restrictor to maintain water pressure while minimizing the amount of water use.

Don’t let the hot water run when doing dishes, shaving, or brushing teeth.

Like a heat pump’s backup heater, a space heater uses electrical resistance heat that can be expensive to operate. That said, they can be useful to heat small areas like the bathroom for short periods of time. In fact, it can be much cheaper to use a space heater in the morning than to raise the temperature in the whole house for a short period of time.

You hear a lot of suggestions and general chatter about making the change from traditional incandescent bulbs to LED. And while we at Kolb Electric generally agree, we noticed something when hopping around on the web. You can find a lot of answers why this is a good idea. But none of it is really…simple. You get charts, math, and massive walls of text, and you know that deep down, somewhere in there lies your answer. If only you could get your eyes to stop glazing over. So we decided to lay it down layman style for our consumers, letting you know the why in a short, succinct bit of information!

There are a few aspects that overall make LED the superior option. Longevity is good, as these lights tend to last much longer, thus need to be purchased less often. They’re also environmentally friendly, and that’s nice too. But when it comes down to it, you care about the efficiency. And this lies in the wattage of the two lighting types.

Light wattage strictly refers to how much energy a light requires to generate lumens (the unit we use to measure light). The big secret between these two light sources lies all in how they generate lumens:

To make it clear, let’s use an example: A standard incandescent bulb generally uses 60 watts of power to generate light. You can get the same amount of light from an LED, for a mere six to eight watts.

So there’s the big answer. The average light wattage of an LED is more desirable, since it requires demonstrably less energy to produce light. The longevity and environmental-friendliness are basically the icing on the technological cake!

You are tired of working at your cubical. You’re dreaming of something bigger. You’re obviously online now and most likely looking for something better. Better is in front of you right now. We are better. No we are not Google, Zappos, or Facebook. We are a local Clive, Iowa, company. And NO we don’t need any money from you. This is a real business and we don’t need you to buy into anything other than our vision. You will be a full time paid team member.

We are not a startup. Our company was founded in 2005. We are financially stable and a leader in our industry. Why the entrepreneur themed vibe? We want to build something better. We want to build something that is truly great. We want to interview 5 leading candidates not 50 bodies.

Benefits:

Discussed at interview but they are well above the industry standard. Hours: 9-5? 8-4? Somewhere around there. We need you here 8 hours per day and it has to be during standard business times. Flexible but simple right?

The proud owner of a generator, whether for general use or use in an emergency, can rest assured that they have access to the power they need. But what if your generator isn’t quite up to the task? This can leave you with no means to perform normal functions at best, and at worst could leave you powerless in the face of a storm or other catastrophe. The certified experts at Kolb Electric have a strong history of handling generators, and today we bring you one of the most common complaints among generator-owners: power surges.

When it comes to communicating signs of disrepair, generators are actually rather talkative. It’s all in understanding the signs, the most common of which coming in the form of surging.

Surging refers to a generator (or other electrical component, machine or device) displaying clear fluctuations in behavior at intervals. These intervals can follow a clear pattern, or can be completely random. What exactly does this mean? Let’s use some examples.

A surging generator often will leave lights burning much brighter, then much dimmer rapidly, causing a sort of flicker back and forth. In machinery, this can also come as drastic changes in pace as well; such as a fan running faster and then slower for no obvious reason.

There are actually numerous causes for generator surging, including:

Bottom line; if your generator is experiencing surging there is definitely something wrong. The causes are myriad, but the solution stays the same. Seek professional assistance for your generator repair to ensure it’s ready and available when you need it most!

At Kolb Electric, we’ve been handling generator installation, repair and replacement for years, and we always bring our very best to any project. if you’re experiencing generator surges, don’t hesitate to contact us right away!